Team:Calgary/Notebook/Protocols/taqpcr
From 2012.igem.org
(9 intermediate revisions not shown) | |||
Line 5: | Line 5: | ||
<p>The following is obtained from the Invitrogen Taq PCR kit (although most PCR kits have similar protocols).</p> | <p>The following is obtained from the Invitrogen Taq PCR kit (although most PCR kits have similar protocols).</p> | ||
- | <center> | + | <center> |
<div style="margin-bottom:60px"> | <div style="margin-bottom:60px"> | ||
<table width="700"> | <table width="700"> | ||
<tr> | <tr> | ||
- | + | <td width="85%"><div class="heading"><center><h3></a>Mastermix setup</h3> </center></p></div></td> | |
</tr> | </tr> | ||
</table> | </table> | ||
Line 71: | Line 71: | ||
</table> | </table> | ||
</center> | </center> | ||
- | <p>< | + | <p><i>Thermocycler Conditions</i></p> |
<ol> | <ol> | ||
- | <li> 1 Cycle - | + | <li> 1 Cycle - 10 minutes at 95°C </li> |
<li> 36 cycles of: | <li> 36 cycles of: | ||
<ol> | <ol> | ||
- | <li type="a"> | + | <li type="a"> 3 minutes at 95°C </li> |
- | <li type="a"> 1 minute at | + | <li type="a"> 1 minute at 55°C (for BioBrick primers) </li> |
- | <li type="a"> 1 minute at 72°C </li> | + | <li type="a"> 1 minute/kb at 72°C </li> |
</ol> | </ol> | ||
</li> | </li> | ||
Line 85: | Line 85: | ||
<p> Conditions were varied as needed. For example in cases of longer products all 1 minute times were increased to 1.5 or even 3 minutes</p> | <p> Conditions were varied as needed. For example in cases of longer products all 1 minute times were increased to 1.5 or even 3 minutes</p> | ||
<p>Follow the same protocol for a colony PCR.</p> | <p>Follow the same protocol for a colony PCR.</p> | ||
+ | |||
+ | <p>We also used a Taq polymerase that we isolated in-house with slightly different cycling conditions. Since this Taq could not tolerate the lysis stage at 95°C for 10 minutes, the cells were lysed in 4 μL of water for 10 minutes before master mix was added. | ||
</div> | </div> | ||
</td> | </td> |
Latest revision as of 03:54, 4 October 2012
![](https://static.igem.org/mediawiki/2012/f/fc/UCalgary2012_MainHeaderImage.png)
![](https://static.igem.org/mediawiki/2012/c/c5/UCalgary2012_HeaderLogoOrange.png)
Hello! iGEM Calgary's wiki functions best with Javascript enabled, especially for mobile devices. We recommend that you enable Javascript on your device for the best wiki-viewing experience. Thanks!
Taq PCR Protocol
The following is obtained from the Invitrogen Taq PCR kit (although most PCR kits have similar protocols).
Mastermix setup |
Reagent | Volume ( 1x ) | Volume ( 3x ) | Volume ( 5x ) | Volume ( 15x ) |
Sterile H2O | 36 μL | 108 μL | 180 μL | 540 μL |
10X Taq Buffer | 5 μL | 15 μL | 25 μL | 75 μL |
2mM dNTPs | 5 μL | 15 μL | 25 μL | 75 μL |
Forward Primer (100 ug/ul) | 1 μL | 3 μL | 5 μL | 15 μL |
Reverse Primer (100 ug/ul) | 1 μL | 3 μL | 5 μL | 15 μL |
50mM MgCl2 | 1.5 μL | 4.5 μL | 7.5 μL | 22.5 μL |
Taq Polymerase (50 ug/ul) | 0.5 μL | 1.5 μL | 2.5 μL | 7.5 μL |
Thermocycler Conditions
- 1 Cycle - 10 minutes at 95°C
- 36 cycles of:
- 3 minutes at 95°C
- 1 minute at 55°C (for BioBrick primers)
- 1 minute/kb at 72°C
- 1 Cycle - 10 minutes at 72°C then HOLD at 4°C
Conditions were varied as needed. For example in cases of longer products all 1 minute times were increased to 1.5 or even 3 minutes
Follow the same protocol for a colony PCR.
We also used a Taq polymerase that we isolated in-house with slightly different cycling conditions. Since this Taq could not tolerate the lysis stage at 95°C for 10 minutes, the cells were lysed in 4 μL of water for 10 minutes before master mix was added.