LB media

Final concentrations:

• 1% (w/v) tryptone
• 0.5% (w/v) yeast extract
• 86 mM NaCl

Per liter:

• 10g Tryptone
• 5g Yeast extract
• 5g NaCl




• 15g Agar -Optional-
• Adjust pH to 7.5 with NaOH 1M

SOB media

Final concentrations:

• 0.5% (w/v) yeast extract
• 2% (w/v) tryptone
• 10 mM NaCl
• 2.5 mM KCl
• 20 mM MgSO4

Per liter:

• 5 g yeast extract
• 20 g tryptone
• 0.584 g NaCl
• 0.186 g KCl
• 2.4 g MgSO4




• 15g Agar -Optional-
• Adjust pH to 7.5 with NaOH 1M

5X Gibson Assembly Isothermal Buffer

Final Concentrations:

• 25% PEG MW 8000
• 500mM Tris HCl pH 7.5
• 50mM CaCl
• 50mM DTT
• 1mM dATP
• 1mM dTTP
• 1mM dGTP
• 1mM dCTP
• 5mM NAD+
• H20 nuclease free

For a 2 mL stock (equivalent to 20 100uL 5X isothermal buffers)

• 0.5g PEG MW 8000
• 1.5mL Tris-HCl pH 7.5 1M

Swivel for 30 minutes in a orbital oscillator for PEG to dissolve fully

• 50uL CaCl 2M
• 100uL DTT 1M
• 20uL dATP 100mM
• 20uL dTTP 100mM
• 20uL dGTP 100mM
• 20uL dCTP 100mM
• 200uL NAD+ 200mM
• H20 nuclease free up to 2mL

Alicuot into 100uL stocks

Store at -80°C

1.33X Gibson Assembly Master Mix

For a 375ul 1.33X Gibson Assembly Master Mix

• 100uL 5X Gibson Assembly Isothermal Buffer
• 6.25uL Phusion Polymerase 2 U/uL (cat N° F-350S) from Thermo Scientific
• 2uL Epicentre T5 Exonuclease 1U/uL (cat N° T5E4111K) from Illumina

It is important to dilute the T5 Exonuclease stock from 10U/uL to 1U/ul to measure the volume correctly

• 50uL Taq DNA Ligase 2000 U/uL (cat N° M208S) from NEB
• 216.75uL of nuclease free H20

Alicuot 9uL in 0.2mL PCR tubes. This will yield about 42 reactions

Gibson Assembly

Design primers

The easiest way to design primers to obtain amplicons with the required overlaps (40bp final overlaps) is to make an in sillico design of the final construct

• Design forward primer of right amplicon of joint in 5'->3' direction
• Calculate length of annealing part of primer as to reach a Tm of approximately 63°C
• Add 20 bp of overlap
• Design reverse primer of left amplicon of joint in 5'->3' direction
• To do this, select full joint and "reverse complement" it (be sure to be able to discriminate between right and left parts of joint)
• Calculate length of annealing part of primer as to reach a Tm of approximately 63°C
• Add 20 bp of overlap
• Apply same principle in all joints

Obtaining parts

• PCR parts using Phusion Polymerase datasheet indications. It is important to use a low ammount of template plasmid (10pg) as to reduce possibility of carry-over during band purification
• Run agarose gel electrophoresis on a adecuate gel (50bp to 200bp parts should be run on a 3% w/v agarose gel, larger parts should be run on a 1% w/v to 1.5% w/v agarose gel) until clear distinction of bands is achieved. It is recommended that gels should be exposed as little as possible to UV transilluminators as UV light damages DNA.
• Cut band and proceed with band purification. Elute in smallest volume as possible according to your kit specification
• Quantify purified DNA

Assembly reaction

The assembly reaction is composed of 9uL of 1.33X Gibson assembly master mix + 3uL of purified parts DNA

• The calculation of the ratio at which your DNA parts are should be in correspondence to the level of competence of your cells. We have found that with our cells (5*10^⁸ colonies/ug of pUC19 DNA) the following ratios work well
• Calculate the amount of pmoles of each purified DNA part using the following equation: pmoles of DNA = Concentration (ng/uL) * 650 Daltons/(1000{nano->pico conversion factor} * base pair length of part)