PCR with Phusion High-Fidelity DNA Polymerase

Tube preparation

Put items in this order:

Component	50µl reaction	Comments
H2O	32
5x Phusion HF Buffer	10
10mM dNTPs	1
Primer FW	2	Primers have to be at 10µM
Primer RV	2	Primers have to be at 10µM
Template DNA	1
DMSO (optional)	1,5	recommended for GC-rich amplicons < 20kb
Phusion DNA polymerase	0,5

Cycling instructions

Cycle step	Temperature	Time	Cycles
Initial denaturation	98°C	4min	1
Denaturation	98°C	20s	30
Annealing	Lower Tm of primers	30s
Extension	72°C	30S/kb
Final extension	72°C	10min	1
Final extension	4°C	hold	1

Préparation of LB medium and LB Agar:

=> LB Agar : -18,5g LB Agar -300ml H2O

=> LB medium : -6g LB broth -300ml de H2O

Autoclaved at 250°C

Gel extraction

1. Excise the DNA fragment from the agarose gel with a clean, sharp scalpel under UV light.
2. Weight the gel slice in a colorless tube. Add 3 volumes of Buffer QG to 1 volume of gel.
3. Incubate at 50°C for 10 min, until the gel slice has completely dissolved.
4. The color of the mixture have to be yellow, otherwise add 10 µl of 3M sodium acetate.
5. Ass 1 gel volume of isopropanol to the sample and mix.
6. Place a spin column in a provided 2 ml collection tube.
7. To bind DNA, apply the sample to the column and centrifugat for 1 min. Discard the flow-through and place the column back into the same tube.
8. To wash, add 0,75 ml of buffer PE to the column and centrifugate for 1 min.Discard the flow-through and place the column back into the same tube.
9. Centrifugate the column in a 2 ml Collection tube for 1 min 17,900xg (13,000 rpm).
10. Place the column into a clean 1,5 ml microcentrifuge tube.
11. to elute DNA, add 15 µl of water to the column and centrifugate for 1 min.

In vitro fecondation of Xenopus tropicalis

2 or 3 days before the IVF

Pre-injection of frogs (males et females)
100µl of hCG (0,1UI/µl, do a dilution by 10 of the commercial solution)

D day

Test the injector before beginning
Inject the 100µl hCG (1UI/µl) in the morning
Isolate the animals : an animal by box

Prepare :
Timer
Methylcellulose (put at room temperature)
Boxes special for injections
Materiel of injection
Capillaires ad hoc with oil
Solutions to inject (add 1µl of blue or red of Nile)
Solution L15/FCS :
- boxes (1/femelle) of Pétri (d=10 cm) lined of L15/FCS (500µl)
- 2 tubes 1,5mL with 250µl of L15/FCS (one for each testicle)
Pestles in plastic cleaned to grind the testicles
MMR 0,1X
MMR 0,05X
MS-222 0,2%

Euthanasia of the male

Put the male in a vat with MS-222 0,2% and look forward to his non response of pinches. Put it out and process of the dissection to extract the two testicles.
For that, dispose the animal: the dorsal face against the dissection board. Pinch the skin in the middle of the belly and do a small incision with scissors; from this point, perform skin incisions shown in the diagram.

Fold the flaps and skin incision in the muscular wall avoiding severing the abdominal vein to avoid hemorrhage. Both gonads are located in the ventral face of kidneys.
Both gonads are located in the ventral surface of the kidneys, they cover more or less and in corpora lutea (fat mass).By extracting them from the abdominal cavity, we can extract the testicles attached to them. The male's testicles are two oval organs, smooth, yellow-pale as can be seen in the photograph below.
Roll the testicles on kitchen paper to remove blood and blood vessels. Dip each testicle in a tube of 1,5mL with 250µl of L15/FCS. Keep tubes on ice. Crush the testicles with a pestle until obtaining a homogeneous solution. Add 250µl of L15/FCS, mix with a P1000 always on ice.

Lay eggs of females

Spawn females (who have already started laying alone) in Petri dishes previously coated with L15/FCS (gently massage into their flanks).

In vitro fecondation

With a pasteur pipette in plastic, remove as much liquid in the Petri dish prior the IVF. Fil 50µl/500eggs of sperm solution on the aggs with P1000 and mix with a cone to evenly distribute the sperm on the eggs. Let the sperm fix on the eggs during 3-5 min.
Activate the spermatozoid by recovering the eggs of MMR 0,05X to allow the fecundation.

Degangage

15 min after fecondation activation, processing of the degangage.
For that, prepare cysteine 2%, pH 7,5-8 :
- Weight 2g of cysteine powder, transfert if in 80 mL of MMR 0,1% and put it in a becher under magnetic agitation. Mesure pH et equilibrate by adding NaOH 1M.
- Complete with MMR 0,1% to 100mL.
Remove MMR 0,05% from the petri box containing the eggs. Add the cysteine and agitate the box by rotation for 2 min.
Transfere eggs in a 100ml pot (red plug) and continue to agitate by rotation for 5-8 min. check that the embryos seem to touch each other to validate the degangage.
Rinse 3 times with MMR 0,1X.

Attention : during the diferent phases of washing, ensure that the eggs are always in liquid.

Add some methylcellulose to eggs to retard the developpement and facilitate the injection.

Place eggs (50-100) in petri boxes special for injection (lined with a small mesh) and inject.

After injections, the embryos are transfered in MMR 0,1% in small petri boxes lined in the background with agarose. Boxes are incubated at 21°C.

Team:Evry/Protocols

From 2012.igem.org

Contents