Team:TU-Eindhoven/Parts

• Introduction
  • Home page
  • Background
    information
  • About us
  • Contact us
  • Our photos
• Project
  • Project description
  • Lab approach
  • Device information
  • Initial model
  • Yeast model
  • Lab results
  • Our BioBricks^TM
  • Our
    accomplishments
• Considerations
  • Public outreach
  • Safety questions
  • Other thoughts
• Future applications
  • Human interest
  • Further
    developments
• Notebook
  • Before week 1
  • Week 1
  • Week 2
  • Week 3
  • Week 4
  • Week 5
  • Week 6
  • Week 7
  • Week 8
  • Week 9
  • Week 10
  • Week 11
  • Week 12
  • After week 12
  • Lab protocols
• Partners
  • ICMS TU/e
  • Team collaborations
  • Attributions and Contributions
  • Our sponsors

Our iGEM team prepared three different BioBricks: BBa_K881000 (R-GECO), BBa_K881001 (G-GECO), BBa_K881002 (B-GECO). These three GECO proteins, which are obtained from Zhao et al. 2011^[1], are red, green and blue fluorescent respectively. The protocol for ligation and restriction obtained from the BioBrick library didn't work for our Biobricks. Therefore, we designed our own protocol, which can be found at the 'Protocol' page, and is shortly described here. The coding DNA for these three proteins was ligated into a <partinfo>pSB1C3</partinfo> vector. After culturing, the vectors were restricted with restriction enzymes XbaI en PstI. These enzymes restricted the vector nicely, however, the DNA sequence coding for the fluorescent GECO proteins appears to contain a restriction site for PstI aswell. Therefore, this procedure was repeated with restriction enzymes XbaI and SpeI. Using this restriction method, the BioBricks can be used in yeast cells and E.coli bacteria.

Although, these BioBricks are prepared in a more efficient way using our own protocol, the permission we needed to apply the GECO BioBricks to registry library was more difficult than expected. You can read more about this struggle at the 'Other Thoughts' page.

Characterization

E. Coli strain BL21 transformed with Part BBa_K881000 and Part BBa_K881001 ligated into vector pET_28a were cultured in LB media containing 100 µg/ml kanamycin for ~4 hours at 37°C. The growth rate was followed by use of OD600 measurements (see figure on the right). Then the culture was induced at an OD600 of 0,82 absorption units with 100 µg/ml IPTG.

Harvesting and Purification

After induction for 15 hours, the cells were harvested and lysed with 5ml BugBuster containing 1µl/ml Benzonase. The supernatant of this suspension was put on a Ni-NTA column for purification and afterwards put on a PD10 column and washed with a TRIS buffer containing NaCl to remove all the calcium molecules. Then, an SDS-gel was prepared to check the abundance and the purity of the GECO proteins (See figure below). As can be seen in the gels, the GECO proteins are present in abundance.

Calcium titration

Before measuring the fluorescence, the samples were prepared first. A 30mM MOPS buffer was prepared containing 100mM KCl and 10mM EGTA. Since EGTA has a high affinity for calcium, in this buffer the GECO proteins will be discomposed from calcium completely. Then 1μl 1mg/ml protein was added to this buffer aswell as a range of calcium concentrations ranging from 0nM to 3,900nM free calcium. Then, the fluorescence of the two GECO proteins, G-GECO and R-GECO, was measured at 20°C. The proteins were excited at 485nm and 565nm respectively. In the figure below, it can be seen that the intensity of the fluorescence increases upon increasing free calcium concentration, suggesting our BioBricks are indeed sensitive to calcium concentrations.

References

• [1] Zhao, Y. et al., An Expanded Palette of Genetically Encoded Ca2+ Indicators, Science 333: 1888-1891, (2011)