"
Team:TU Darmstadt/Protocols/DNA Quantification / NanoDrop
From 2012.igem.org
(Difference between revisions)
| (One intermediate revision not shown) | |||
| Line 27: | Line 27: | ||
<li><a href="/Team:TU_Darmstadt/Safety" title="Safety">Safety</a></li> | <li><a href="/Team:TU_Darmstadt/Safety" title="Safety">Safety</a></li> | ||
<li><a href="/Team:TU_Darmstadt/Downloads" title="Downloads">Downloads</a></li></ul></li> | <li><a href="/Team:TU_Darmstadt/Downloads" title="Downloads">Downloads</a></li></ul></li> | ||
| - | <li><a href="/Team:TU_Darmstadt/Human_Practice" title="Human Practice">Human Practice</a | + | <li><a href="/Team:TU_Darmstadt/Human_Practice" title="Human Practice">Human Practice</a></li> |
| - | + | ||
| - | + | ||
| - | + | ||
<li><a href="/Team:TU_Darmstadt/Sponsors" title="Sponsors">Sponsors</a><ul> | <li><a href="/Team:TU_Darmstadt/Sponsors" title="Sponsors">Sponsors</a><ul> | ||
<li><a href="/Team:TU_Darmstadt/Sponsors" title="Sponsors">Overview</a></li> | <li><a href="/Team:TU_Darmstadt/Sponsors" title="Sponsors">Overview</a></li> | ||
| Line 53: | Line 50: | ||
#At the end load your blank and click '''Measure''' to test the blank. | #At the end load your blank and click '''Measure''' to test the blank. | ||
#If the measurement deviates more than 5 ng/µL from 0.0 ng/µL, load the blank again, click '''Blank''' and measure your DNA samples. | #If the measurement deviates more than 5 ng/µL from 0.0 ng/µL, load the blank again, click '''Blank''' and measure your DNA samples. | ||
| - | ==== | + | ==== Shimadzu BioSpec Nano ==== |
Switch the NanoDrop ON make sure a wiper is attatched. | Switch the NanoDrop ON make sure a wiper is attatched. | ||
# Press F3 to blank with 2µl of dH<sub>2</sub>O eg. | # Press F3 to blank with 2µl of dH<sub>2</sub>O eg. | ||
# Put 1-2µl of solution of the NanoDrop lense | # Put 1-2µl of solution of the NanoDrop lense | ||
# Press F4 to measure | # Press F4 to measure | ||
Latest revision as of 21:28, 26 September 2012
Contents |
DNA Quantification
Visual Comparison
It is possible to determine DNA concentrations by comparing the relative intensity of PCR bands and marker in agarose gel.
Nanodrop
DNA absorbs light at 260 nm and thus the concentration can be measured photometrically using the [http://www.nanodrop.com/Library/nd-1000-v3.7-users-manual-8.5x11.pdf NanoDrop 1000 Spectrophotometer].
NanoDrop 1000
- Start the programme for the NanoDrop 1000 and click Nucleic Acids
- Pipette 1.5 µL of a water sample onto the lower measurement and click “OK”
- Load your blank and click Blank
- Load your DNA samples and click Measure. A 260/280 ration of 1.8 or above means the sample can be seen as pure
- At the end load your blank and click Measure to test the blank.
- If the measurement deviates more than 5 ng/µL from 0.0 ng/µL, load the blank again, click Blank and measure your DNA samples.
Shimadzu BioSpec Nano
Switch the NanoDrop ON make sure a wiper is attatched.
- Press F3 to blank with 2µl of dH2O eg.
- Put 1-2µl of solution of the NanoDrop lense
- Press F4 to measure
