Team:Trieste/project/modeling

From 2012.igem.org

Revision as of 09:27, 26 September 2012 by Srebrnicaljaz (Talk | contribs)

Modeling

More

Assumptions

  • No interaction with living tissue

Model description

We chose to use a deterministic, empirical model because it gives simple, clean solutions.

The model is composed of 6 variables with 15 parameters. Each variable describes the concentration of a substance inside or outside the bacteria. The variables are:

  • \(b\) - bacteria concentration
  • \(p\) - CymR concentration
  • \(c\) - p-cumate concentration
  • \(l_i\) - internal toxin concentration
  • \(l_e\) - external toxin concentration
  • \(a\) - antibody concentration
All the \(\delta_i\) parameters represent the variable's decay over time.

The first equation, describing the bacteria concentration in the media (bacteria growth) is based on the logistics function: \begin{equation} \dot{x} = x (1-x) \end{equation} We added a term to model bacteria death due to toxin, so the complete equation is: \begin{equation} \dot{b} = k_1 b (N - b) - k_2 b (l_i + l_e) \end{equation} There are three parameters that control this model's behaviour. The \(N\) parameter specifies the maximum concentration of bacteria. The \(k_1\) parameter controls the growth speed and the \(k_2\) parameter sets how powerful the toxin is.

The next equation models the CymR concentration inside the bacteria. \begin{equation} \dot{p} = k_3 - \delta_1 p - \alpha p c \end{equation} The \(k_3\) parameter determines the rate of synthesis of CymR and \(\alpha\) the rate of cumate ligation.

The p-cumate concentration function is in fact a parameter, because it is directly controllable by adding p-cumate into the bacteria solution. \begin{equation} \dot{c} = k_4 - \delta_2 c \end{equation} The \(k_4\) parameter models p-cumate increase (adding p-cumate at a steady rate).

We use two equations to better model the toxin concentration, taking into account the concentration of toxin both inside and outside the bacteria. The equation for the inside concentration is a Hill equation for the inhibitory effect of CymR (\(p\)) on the biosynthesis of the toxin, and the decay term. We used it because the concentration increases until the saturation is reached, and from then on the bacteria stops producing the toxin. The outside equation is the most complex one; the outside toxin concentration depends on bacteria death: when the bacteria dies, all the toxin it has produced is released outside. \begin{align} \dot{l_i} &= \frac{A}{k_5 + p} -\delta_3 l_i \\ \dot{l_e} &= v (l_i + l_e) b l_i - \delta_4 l_e \end{align} The \(A\) parameter sets the maximum toxin concentration inside the bacteria, while the \(v\) parameter takes into account the toxin dilution in the bacteria solution and the toxin strength.

Last but not least, the antibody density, which we suppose always increasing in time. \begin{equation} \dot{a} = k_6 - \delta_5 a \end{equation}

Tools

We decided to use Octave, the open source alternative to Matlab as the framework for our model.

Simulations

No cumate

This is a simulation of our model with no cumate added. We can see the bacteria growing, producing antibodies, and the toxin remains under the kill threshold. Model without cumato

This is a simulation with cumate added. We can see the initial bacteria growth, but then the toxin concentration rises above the toxic levels and bacteria start dying. Eventually, antibody concentration starts to lower as the bacteria die, and the toxin in the bacteria medium rises exponentially. Model with cumato

Team iGEM 2012

Contact us

For other information, write to:

igem2012@gmail.com
Università degli studi di Trieste ICGEB Illy Fondazione Cassa di Risparmio
iGEM 2012 iGEM 2012 iGEM 2012 iGEM 2012 iGEM 2012 iGEM 2012
HTML Hit Counter