I. E. coli strains

  MC1061 : F− araD139, Δ(ara-leu)7696,galE15, galK16, Δ(lac)X74, rpsL (Strr), hsdR2 (rK−mK+), mcrA mcrB1

  TOP10 (Invitrogen) : F- mcrA Δ(mrr-hsdRMS-mcrBC) φ80lacZΔM15 ΔlacX74 nupG recA1 araD139 Δ(ara-leu)7697 galE15 galK16 rpsL(StrR) endA1 λ-

2.Plasmids

pP70 : plasmid which contains the microcin C7 operon and a resistance to chloramphenicol

pCID909 : plasmid which contains the microcin B17 operon and a resistance to ampicilin

pBAD18: arabinose-inducible vector containing kanamicyn resistance

pBAD33: arabinose-inducible vector containing chloramphenicol resistance

pSB1K3 : standard iGEM plasmid which has a resistance to Kanamycin

pSB1C3 : standard iGEM plasmid which has a resistance to Chloramphenicol

pSB1A3 : standard iGEM plasmid which has a resistance to Ampicilin

3. Primers

The following primers were produced by Sigma-Aldrich and the sequences are shown in a 5’-3’ orientation.

3.1. Primers for first amplification of each gene

  MccBA-FOR

  MccBA-REV

   MccBB-FOR

   MccBB-REV

   MccBC-FOR

  MccBC-REV

  MccBE-FOR

  MccBE-REV

  MccBF-FOR

  MccBF-REV

  MccCC-FOR

  MccCC-REV

  MccCF-FOR

  MccCF-REV

3.2. Primers for second amplification

  Common-FOR

  Common-REV

3.3. Primers for insertion in immunity pBAD plasmid

  ImMccBG-FOR

  ImMccBG-REV

  ImMccCF-FOR

  ImMccCF-REV

  ImMccCEFOR

  ImMccCEREV

3.4. Primers for fixing BE

  MccCB Endo For

  MccCB Endo Rev

  MccCB synthgene For1

  MccCB synthgene Rev1

  MccCB synthgene For2

  MccCB synthgene Rev2

4. Kits

Gel purification kit: Sigma-Aldrich, GenEluteTm PCR Clean-up (ref:NA1020)

Mini prep kit: Zymo Research, ZyppyTM Plasmid Miniprep Kit (ref: D4036)

5. Restriction

• Run a PCR to amplify the genes of interest with floating restriction sites.

• Digest the PCR product and the vector by the appropriate restriction enzymes.

     Restriction mix for the PCR products (insert):

       *Xµl of PCR products (X depending on the concentration of insert of the PCR products).

       *1µl of each restriction enzyme.

       *2µl appropriate buffer 10X.

       *Add Yµl bi-distilled water to reach a final volume of 20µl.

     Restriction mix for the vector:

       *200ng of vector.

       *1µl of each restriction enzyme.

       *2µl appropriate buffer 10X.

       *Add Xµl bi-distilled water to reach a final volume of 20µl.

• Incubate for one hour at 37°C

6. Ligation

• The ligation reaction proceeds with 100ng of restricted vector. The quantity of the PCR products is calculated according to the following formula: (100ng vector x PCR product size x 3)/(vector size) = PCR product quantity in ng.

     Ligation mix:

       *1µl T4 DNA ligase.

       *2µl buffer (10x).

       *Add the two restrictions reactions in a final volume of 20µl.

       *Add bi-distilled water for a final volume of 20µl.

       *ADN

• Incubate the ligation reaction overnight at room temperature.

• Electroporate the ligation on bacteria.

7. Preparation of electrocompetent cells

• Dilute 100x an overnight culture in LB medium and incubate at 30°C with shaking until the OD600nm reaches 0.5.

• Centrifuge in a cold rotor at 4500 rpm 4°C for 30 minutes.

• Remove supernatant, resuspend in 20ml cold H20, then centrifuge as above. Repeat this step twice.

• Remove supernatant, resuspend in 10ml cold glycerol, then centrifuge as above.

• Remove final supernatant carefully, resuspend in 1ml cold glycerol.

• Store it at -80°C.

8. Electroporation

   DNA dialysis:

• Fill a petri dish with dH2O.

• Make float a round 0.025µm Millipore dialysis filter on dH2O.

• Place the DNA on the Filter for 20 min, then take it back.

   Electroporation:

• Add dialysed DNA in 50µl of electrocompetent cells.

• Put mixture in an electroporation cuvette.

• Electroporate it at 2,500 volt, 200Ω and 25µFD.

• Add quickly 1ml of LB.

• Put the bacteria for 1 hours at 37°C.

• Plate the volume you need on dish (with appropriate antibiotics).