Team:University College London/LabBook/Week9

Step 1 – Creating culture media: In a sterile environment, set up X numbers of falcons, each with 5mls of media.

Step 2 - Inoculating Colonies into a Selective Broth:: Add Yul of antibiotic to reach desired antibiotic concentration.

(For Ampicillin this is 50ug/ml, For Kanamycin it is 25ug/ml, for Tetracycline it is 15ug/ml, and for Chloramphenicol it is 25ug/ml)

Step 4 – Selecting a Colony: Select a clear, isolated colony and using an inoculation hoop scoop up a colony onto the tip. Deposit in the falcon tube

Step 5 - Culture: Culture your falcon tubes overnight at a temperature of 37 oC. Leave for no longer than 16 hours.

Step 1 - Pellet Cells: Pellet 1.5-5ml bacterial culture containing the plasmid by centrifugation g = 6000

Time = 2 min

Temperature = (15-25oC)

Step 2 - Resuspend Cells: Add 250ul S1 to the pellet and resuspend the cells completely by vortexing or pipetting. Transfer the suspension to a clean 1.5ml microcentrifuge tube.

Step 3 - Puncturing Cell Membrane: Add 250ul S2 gently mix by inverting the tube 4-6 times to obtain a clear lysate. Incubate on ice or at room temperature for NOT longer than 5 min.

Step 4 - Neutralising S2: Add 400ul Buffer NB and gently mix by inverting the tube 6-10 times, until a white precipitate forms.

Step 5 - Centrifuge:

g: 14000

Time:10 minutes

Temperature: (15-25oC)

Step 6 - Centrifuge: Transfer the supernatant into a column assembled in a clean collection tube (provided. Centrifuge:

g = 10,000

Time: 1 minute

Temperature: (15-25oC)

Step 7 - Wash Column: Discard the flow-through and wash the spin column by adding 700ul of Wash Buffer. Centrifuge:

g - 10,000

Time - 1 minute

Temperature: (15-25oC)

Step 8 - Remove residual ethanol: Centrifuge:

g - 10,000

Time - 1 minute

Temperature: (15-25oC)

Step 9 - Elute DNA: Place the column into a clean microcentrifuge tube. Add 50-100ul of Elution Buffer, TE buffer or sterile water directly onto column membrane and stand for 1 min. Centrifuge:

g - 10,000

Time - 1 minute

Temperature: (15-25oC)

Step 10 - Storage: Store DNA at 4oC or -20oC

Preparing the Gel

Step 1: Within a conical flask, add 3ml 50X TAE, 1.5g Agarose, and 150ml RO water

Step 2: Heat for 1 min in microwave. Swirl. Heat again for 30s. If solution is clear stop. Else repeat.

Step 3: Cool solution under running cold water.

Step 4: Add 20ul ethidium bromide (normal concentration of EB solution is 500ug/ul)

Step 5: Pour into a sealed casting tray in a slow steady stream, ensuring there are no bubbles

Running a gel

Step 6: Add 1 part loading buffer to five parts of loading sample

Step 7: Position the gel in the tank and add TAE buffer, enough to cover the gel by several mm

Step 8: Add 5ul of DNA ladder to lane 1

Step 9: Add samples to the remaining wells

Step 10: Run at 100 volts for 1hour and 15 minutes

Imaging the Gel

Step 11: Place gel in GelDoc 2000 chamber

Step 12: Turn GelDoc 2000 chamber on 

Step 13: From computer: Quantity One > Scanner > Gel_Doc_Xr>Manuqal Acquire

Step 14: Alter the exposure/settings to give a clear image.

TAE - Tris-acetate-EDTA

EDTA - ethylenediamine tetraacetic acid

Step 1 – Creating culture media: In a sterile environment, set up X numbers of falcons, each with 5mls of media.

Step 2 - Inoculating Colonies into a Selective Broth:: Add Yul of antibiotic to reach desired antibiotic concentration.

(For Ampicillin this is 50ug/ml, For Kanamycin it is 25ug/ml, for Tetracycline it is 15ug/ml, and for Chloramphenicol it is 25ug/ml)

Step 4 – Selecting a Colony: Select a clear, isolated colony and using an inoculation hoop scoop up a colony onto the tip. Deposit in the falcon tube

Step 5 - Culture: Culture your falcon tubes overnight at a temperature of 37 oC. Leave for no longer than 16 hours.

Step 1 - Pellet Cells: Pellet 1.5-5ml bacterial culture containing the plasmid by centrifugation g = 6000

Time = 2 min

Temperature = (15-25oC)

Step 2 - Resuspend Cells: Add 250ul S1 to the pellet and resuspend the cells completely by vortexing or pipetting. Transfer the suspension to a clean 1.5ml microcentrifuge tube.

Step 3 - Puncturing Cell Membrane: Add 250ul S2 gently mix by inverting the tube 4-6 times to obtain a clear lysate. Incubate on ice or at room temperature for NOT longer than 5 min.

Step 4 - Neutralising S2: Add 400ul Buffer NB and gently mix by inverting the tube 6-10 times, until a white precipitate forms.

Step 5 - Centrifuge:

g: 14000

Time:10 minutes

Temperature: (15-25oC)

Step 6 - Centrifuge: Transfer the supernatant into a column assembled in a clean collection tube (provided. Centrifuge:

g = 10,000

Time: 1 minute

Temperature: (15-25oC)

Step 7 - Wash Column: Discard the flow-through and wash the spin column by adding 700ul of Wash Buffer. Centrifuge:

g - 10,000

Time - 1 minute

Temperature: (15-25oC)

Step 8 - Remove residual ethanol: Centrifuge:

g - 10,000

Time - 1 minute

Temperature: (15-25oC)

Step 9 - Elute DNA: Place the column into a clean microcentrifuge tube. Add 50-100ul of Elution Buffer, TE buffer or sterile water directly onto column membrane and stand for 1 min. Centrifuge:

g - 10,000

Time - 1 minute

Temperature: (15-25oC)

Step 10 - Storage: Store DNA at 4oC or -20oC

Preparing the Gel

Step 1: Within a conical flask, add 3ml 50X TAE, 1.5g Agarose, and 150ml RO water

Step 2: Heat for 1 min in microwave. Swirl. Heat again for 30s. If solution is clear stop. Else repeat.

Step 3: Cool solution under running cold water.

Step 4: Add 20ul ethidium bromide (normal concentration of EB solution is 500ug/ul)

Step 5: Pour into a sealed casting tray in a slow steady stream, ensuring there are no bubbles

Running a gel

Step 6: Add 1 part loading buffer to five parts of loading sample

Step 7: Position the gel in the tank and add TAE buffer, enough to cover the gel by several mm

Step 8: Add 5ul of DNA ladder to lane 1

Step 9: Add samples to the remaining wells

Step 10: Run at 100 volts for 1hour and 15 minutes

Imaging the Gel

Step 11: Place gel in GelDoc 2000 chamber

Step 12: Turn GelDoc 2000 chamber on 

Step 13: From computer: Quantity One > Scanner > Gel_Doc_Xr>Manuqal Acquire

Step 14: Alter the exposure/settings to give a clear image.

TAE - Tris-acetate-EDTA

EDTA - ethylenediamine tetraacetic acid

Step 1 - Setting up PCR tubes: Thaw reagents and add to PCR tubes in the proportions described in the table below

PCR Components	Volume (ul)
5x Reaction Buffer	10
25mM MgCl2	4
10mM dNTPs	1
10uM Forward primer	5
10uM Reverse primer	5
DNA Polymerase	0.25
Nuclease Free Water	24.25
Template DNA	0.5
Total Volume	0.5

Step 2 - PCR program: Add PCR tubes to a thermocycler and run under the following conditions.

PCR conditions	Temp (oC)	Time (s)
Initial Denaturation (1 cycle)	95	30
Denaturation/Annealing/Extension (30 cycles)	95/55/72	10/25/120
Final Extension (1 cycle)	72	600
Hold	4	∞

Preparing the Gel

Step 1: Within a conical flask, add 3ml 50X TAE, 1.5g Agarose, and 150ml RO water

Step 2: Heat for 1 min in microwave. Swirl. Heat again for 30s. If solution is clear stop. Else repeat.

Step 3: Cool solution under running cold water.

Step 4: Add 20ul ethidium bromide (normal concentration of EB solution is 500ug/ul)

Step 5: Pour into a sealed casting tray in a slow steady stream, ensuring there are no bubbles

Running a gel

Step 6: Add 1 part loading buffer to five parts of loading sample

Step 7: Position the gel in the tank and add TAE buffer, enough to cover the gel by several mm

Step 8: Add 5ul of DNA ladder to lane 1

Step 9: Add samples to the remaining wells

Step 10: Run at 100 volts for 1hour and 15 minutes

Imaging the Gel

Step 11: Place gel in GelDoc 2000 chamber

Step 12: Turn GelDoc 2000 chamber on 

Step 13: From computer: Quantity One > Scanner > Gel_Doc_Xr>Manuqal Acquire

Step 14: Alter the exposure/settings to give a clear image.

TAE - Tris-acetate-EDTA

EDTA - ethylenediamine tetraacetic acid

Step 1 - Setting up PCR tubes: Thaw reagents and add to PCR tubes in the proportions described in the table below

PCR Components	Volume (ul)
5x Reaction Buffer	10
25mM MgCl2	4
10mM dNTPs	1
10uM Forward primer	5
10uM Reverse primer	5
DNA Polymerase	0.25
Nuclease Free Water	24.25
Template DNA	0.5
Total Volume	0.5

Step 2 - PCR program: Add PCR tubes to a thermocycler and run under the following conditions.

PCR conditions	Temp (oC)	Time (s)
Initial Denaturation (1 cycle)	95	30
Denaturation/Annealing/Extension (30 cycles)	95/55/72	10/25/120
Final Extension (1 cycle)	72	600
Hold	4	∞

Preparing the Gel

Step 1: Within a conical flask, add 3ml 50X TAE, 1.5g Agarose, and 150ml RO water

Step 2: Heat for 1 min in microwave. Swirl. Heat again for 30s. If solution is clear stop. Else repeat.

Step 3: Cool solution under running cold water.

Step 4: Add 20ul ethidium bromide (normal concentration of EB solution is 500ug/ul)

Step 5: Pour into a sealed casting tray in a slow steady stream, ensuring there are no bubbles

Running a gel

Step 6: Add 1 part loading buffer to five parts of loading sample

Step 7: Position the gel in the tank and add TAE buffer, enough to cover the gel by several mm

Step 8: Add 5ul of DNA ladder to lane 1

Step 9: Add samples to the remaining wells

Step 10: Run at 100 volts for 1hour and 15 minutes

Imaging the Gel

Step 11: Place gel in GelDoc 2000 chamber

Step 12: Turn GelDoc 2000 chamber on 

Step 13: From computer: Quantity One > Scanner > Gel_Doc_Xr>Manuqal Acquire

Step 14: Alter the exposure/settings to give a clear image.

TAE - Tris-acetate-EDTA

EDTA - ethylenediamine tetraacetic acid

Software ND-1000 Model:

Step 1: Initialise the spectrophotometer by pipetting 1 µ of clean water onto lower optic surface, lowering the lever arm and selecting ‘initialise’ in the ND-1000 software

Step 2: Wipe and add elution buffer as negative control. Click blank in ND-1000 software

Step 3: Wipe and add 1 µl sample

Step 4: On the software set lambda to 260nm

Step 5: Lower the lever arm and click measure in ND-1000 software

Step 6: Take readings for concentration and purity

Step 7: Once measurement complete, wipe surface

Step 1 - Picking Colony: Using a pipette select an isolated colony

Step 2 - Deposit: Dip the colony in 10ul of dH20, preferably in screw top container

Step 3 - Boiling Stage:Boil the dH20 100 for 5-10mins

Step 4 - Centrifuge:

Time: 1 min

RPM: 8000

Temp: 18oC

Step 5 - Remove Supernatant: The supernatant contains the DNA template.

Primers should be designed to:

1) Be 18-25 nucleotides in length

2) Have a melting temperature that does not differ by more than 5oC between the two primers of a pair

3) GC nucleotides should constitute 40-60%

4) Have a 3’primer end that is not complimentary to any region of the primer pair

5) Contain an equal distribution of the nucleotides

6) Closely match the target sequence (and so known polymorphic sites are avoided)

7) Have a GC clamp on either end

Step 1 - Setting up PCR tubes: Thaw reagents and add to PCR tubes in the proportions described in the table below

PCR Components	Volume (ul)
5x Reaction Buffer	10
25mM MgCl2	4
10mM dNTPs	1
10uM Forward primer	5
10uM Reverse primer	5
DNA Polymerase	0.25
Nuclease Free Water	24.25
Template DNA	0.5
Total Volume	0.5

Step 2 - PCR program: Add PCR tubes to a thermocycler and run under the following conditions.

PCR conditions	Temp (oC)	Time (s)
Initial Denaturation (1 cycle)	95	30
Denaturation/Annealing/Extension (30 cycles)	95/55/72	10/25/120
Final Extension (1 cycle)	72	600
Hold	4	∞

Preparing the Gel

Step 1: Within a conical flask, add 3ml 50X TAE, 1.5g Agarose, and 150ml RO water

Step 2: Heat for 1 min in microwave. Swirl. Heat again for 30s. If solution is clear stop. Else repeat.

Step 3: Cool solution under running cold water.

Step 4: Add 20ul ethidium bromide (normal concentration of EB solution is 500ug/ul)

Step 5: Pour into a sealed casting tray in a slow steady stream, ensuring there are no bubbles

Running a gel

Step 6: Add 1 part loading buffer to five parts of loading sample

Step 7: Position the gel in the tank and add TAE buffer, enough to cover the gel by several mm

Step 8: Add 5ul of DNA ladder to lane 1

Step 9: Add samples to the remaining wells

Step 10: Run at 100 volts for 1hour and 15 minutes

Imaging the Gel

Step 11: Place gel in GelDoc 2000 chamber

Step 12: Turn GelDoc 2000 chamber on 

Step 13: From computer: Quantity One > Scanner > Gel_Doc_Xr>Manuqal Acquire

Step 14: Alter the exposure/settings to give a clear image.

TAE - Tris-acetate-EDTA

EDTA - ethylenediamine tetraacetic acid

Step 1 - Prepare: Set out the Congo Red plates already prepared.

Step 2 - Streak Cells: Streak a sample of control cells (cells not expressing Curli) onto one antiobiotic-free congo red plate, and onto one antibiotic-inoculated congo red plate. Do the same for the curli-expressing cell line.

Step 3 - Incubate: Incubate cells overnight at 37oC or over the weekend at 30oC.