Team:University College London/LabBook/Week14

Step 1 - Addition of BioBrick: To the still frozen competent cells, add 1 - 5 µL of the resuspended DNA to the 2ml tube.

Step 4 - Incubation: Close tube and incubate the cells on ice for 45 minutes.

Step 5 - Heat Shock: Heat shock the cells by immersion in a pre-heated water bath at 37ºC for 10 minutes.

Step 6 - Incubation: Incubate the cells on ice for 2 minutes.

Step 7 - Add media: Add 1.5ml of Lysogeny Broth and transfer to a falcon tube.

Step 8 - Incubation: Incubate the cells at 37ºC for 1 hour at RPM 550. 

Step 9 - Transfer: transfer the solution back into a 1.5ml Eppendorf and centrifuge

RPM: 14000

Time: 2 minutes

Temperature (18-25oC)

Step 10 - Resuspend:Remove supernatant and resuspend in 100ul LB

Step 11 - Plating: Spread the resuspended cell solution onto a selective nutrient agar plate. Place the plates in a 37°C static incubator, leave overnight (alternatively a 30°C static incubator over the weekend)

Step 1 -Creating culture media: In a sterile environment, set up a falcons, with 5mls of Lysogeny Broth and 100ul 1M MgS04.

Step 2 – Selecting a Colony: Select a clear, isolated colony and using an inoculation hoop, scoop up a colony onto the tip. Deposit in the falcon tube

Step 3 - Cell culture: Culture your falcon tubes overnight at a temperature of 37 oC. Leave for no longer than 16 hours.

Step 1 – Innoculation: Inoculate 100mls of Lysogeny Broth in pre-warmed conical with 1ml of the overnight culture from Day 2

Step 2 – Incubation: Incubate for two hours in a 37oC shaker until the cells are at the early log phase of the growth curve. Measure absorbance on a spectrometer until A6000 is approximately 0.3.

Step 3 – Incubation: Transfer to a chilled sterile 50ml Falcon tube and incubate on ice for 10 minutes Step 4 – Centrifuge:

-Time: 5 mins -G – 3300 -Temperature: 180C

Step 5 – Incubate: Resus in 10ml of ice cold 0.1M CaCl2 in 15% glycerol and incubate on ice for 30 minutes.

Step 6 – Centrifuge: -Time: 5 mins -G – 3300 -Temperature: 180C

Step 7 – Transfer: Resus in 1ml of ice cold 0.1M CaCl2 in 15% glycerol. Transfer 100ul aliquots to pre-chilled, pre-labelled eppendorf tubes. Store at -70oC

Step 8 – Centrifuge -Time: 5 mins -G – 3300 -Temperature: 180C

Step 9 - Storage: Store cells at -80oC

Step 1 - Addition of BioBrick: To the still frozen competent cells, add 1 - 5 µL of the resuspended DNA to the 2ml tube.

Step 4 - Incubation: Close tube and incubate the cells on ice for 45 minutes.

Step 5 - Heat Shock: Heat shock the cells by immersion in a pre-heated water bath at 37ºC for 10 minutes.

Step 6 - Incubation: Incubate the cells on ice for 2 minutes.

Step 7 - Add media: Add 1.5ml of Lysogeny Broth and transfer to a falcon tube.

Step 8 - Incubation: Incubate the cells at 37ºC for 1 hour at RPM 550. 

Step 9 - Transfer: transfer the solution back into a 1.5ml Eppendorf and centrifuge

RPM: 14000

Time: 2 minutes

Temperature (18-25oC)

Step 10 - Resuspend:Remove supernatant and resuspend in 100ul LB

Step 11 - Plating: Spread the resuspended cell solution onto a selective nutrient agar plate. Place the plates in a 37°C static incubator, leave overnight (alternatively a 30°C static incubator over the weekend)

Step 1 - Picking Colony: Using a pipette select an isolated colony

Step 2 - Deposit: Dip the colony in 10ul of dH20, preferably in screw top container

Step 3 - Boiling Stage:Boil the dH20 100 for 5-10mins

Step 4 - Centrifuge:

Time: 1 min

RPM: 8000

Temp: 18oC

Step 5 - Remove Supernatant: The supernatant contains the DNA template.

Step 2 - Adding Ingredient: Add the following ingredients to autoclaved/sterile eppendorf tubes

Insert Table

Step 3 - Addition of BioBrick: Flick contents gently and centrifuge.

Step 4 - Centrifuge:

RPM: 14000

Time: 1 minute

Temperature: 18oC

Step 5 - Digest Program: Place the samples on a thermocycler under the following conditions:

RPM: 550

Time: 1 hour

Temperature: 37oC

Step 6 - Denaturing Enzymes: If you are not running the samples on a gel immediately, denature the restriction enzymes by running the samples on a thermocycler under the following conditions:

RPM: 550

Time: 25 minutes

Temperature: 65oC

Temperature: 18oC

Preparing the Gel

Step 1: Within a conical flask, add 3ml 50X TAE, 1.5g Agarose, and 150ml RO water

Step 2: Heat for 1 min in microwave. Swirl. Heat again for 30s. If solution is clear stop. Else repeat.

Step 3: Cool solution under running cold water.

Step 4: Add 20ul ethidium bromide (normal concentration of EB solution is 500ug/ul)

Step 5: Pour into a sealed casting tray in a slow steady stream, ensuring there are no bubbles

Running a gel

Step 6: Add 1 part loading buffer to five parts of loading sample

Step 7: Position the gel in the tank and add TAE buffer, enough to cover the gel by several mm

Step 8: Add 5ul of DNA ladder to lane 1

Step 9: Add samples to the remaining wells

Step 10: Run at 100 volts for 1hour and 15 minutes

Imaging the Gel

Step 11: Place gel in GelDoc 2000 chamber

Step 12: Turn GelDoc 2000 chamber on 

Step 13: From computer: Quantity One > Scanner > Gel_Doc_Xr>Manuqal Acquire

Step 14: Alter the exposure/settings to give a clear image.

TAE - Tris-acetate-EDTA

EDTA - ethylenediamine tetraacetic acid

Step 1 - Setting up PCR tubes: Thaw reagents and add to PCR tubes in the proportions described in the table below

Step 2 - PCR program: Add PCR tubes to a thermocycler and run under the following conditions.

Preparing the Gel

Step 1: Within a conical flask, add 3ml 50X TAE, 1.5g Agarose, and 150ml RO water

Step 2: Heat for 1 min in microwave. Swirl. Heat again for 30s. If solution is clear stop. Else repeat.

Step 3: Cool solution under running cold water.

Step 4: Add 20ul ethidium bromide (normal concentration of EB solution is 500ug/ul)

Step 5: Pour into a sealed casting tray in a slow steady stream, ensuring there are no bubbles

Running a gel

Step 6: Add 1 part loading buffer to five parts of loading sample

Step 7: Position the gel in the tank and add TAE buffer, enough to cover the gel by several mm

Step 8: Add 5ul of DNA ladder to lane 1

Step 9: Add samples to the remaining wells

Step 10: Run at 100 volts for 1hour and 15 minutes

Imaging the Gel

Step 11: Place gel in GelDoc 2000 chamber

Step 12: Turn GelDoc 2000 chamber on 

Step 13: From computer: Quantity One > Scanner > Gel_Doc_Xr>Manuqal Acquire

Step 14: Alter the exposure/settings to give a clear image.

TAE - Tris-acetate-EDTA

EDTA - ethylenediamine tetraacetic acid

Step 1 - Setting up PCR tubes: Thaw reagents and add to PCR tubes in the proportions described in the table below

Step 2 - PCR program: Add PCR tubes to a thermocycler and run under the following conditions.

</html></div></html>

Step 2 - Aim:

To check whether PCR is successful. After the PCR reaction, we can detect the presence of the correct products by running a 1% gel electrophoresis.

Methods:

Results:

The following gel results indicate whether PCR was successful.

Conclusion:

Since we obtained the expected bands in the gel, the PCR was considered successful and the purified DNA used in the 3A ligation.