|
|
| (One intermediate revision not shown) |
| Line 227: |
Line 227: |
| | | | |
| | </html> | | </html> |
| | + | |
| | | | |
| | =Agarose Gel Electrophoresis= | | =Agarose Gel Electrophoresis= |
| Line 251: |
Line 252: |
| | | | |
| | | | |
| - | ===The Difficulty of Large Fragments Assembly===
| |
| - | The general digestion connection will leave scar and will be limited by the specific cleavage sequences.
| |
| - | [[file:TJU2012-Proj-LMR-fig-2.png|thumb|150px|center|'''Figure 2.''' Enzyme digestion (from the website of dnaQ]]
| |
| - | Long PCR fragment will suffer the decline of success rate and distortion, etc.
| |
| - | [[file:TJU2012-Proj-LMR-fig-3.png|thumb|500px|center|'''Figure 3.''' PCR Recombinant & PCR Machine (from the website of dnaQ]]
| |
| - | However, the construction of some large fragments cannot be avoided, so the development of a low-cost, simple operation, good fidelity, a little limiting factor large DNA fragment assembly method is particularly important.
| |
| - |
| |
| - | =Yeast Assembler=
| |
| - | ===History===
| |
| - | Yeast Assembler is based on in vivo homologous recombination in yeast. As for its high efficiency and ease to work with, in vivo homologous recombination in yeast has been widely used for gene cloning, plasmid construction and library creation. In the early of 2008, Zengyi Shao from University of lllinois at Urbana-Champaign, Urbana, used such a method to construct biochemical pathways. Such a method, for its high efficiency in assembling multiple genes, received great popularity since its appearance.
| |
| - |
| |
| - | ===Principles===
| |
| - | One step assembly into a vector.
| |
| - | [[file:TJU2012-Proj-LMR-fig-4.png|thumb|500px|center|'''Figure 4.''' Principles of Yeast assembler (from "DNA assembler, an in vivo genetic method for rapid construction of biochemical pathways")]]
| |
| - | When parts are transformed all parts into Yeast, homologous recombination occurs at the site “x”, and then all little parts are integrated into a vector.
| |
| | | | |
| - | ===Advantages and Disadvantages===
| |
| - | Compared with other methods，the “Yeast assembler” are more efficient and useful for large gene assemble.
| |
| - | [[file:TJU2012-Proj-LMR-fig-5.png|thumb|500px|center|'''Figure 5.''' Advantages and disadvantages of three assemble methods (from "DNA assembler, an in vivo genetic method for rapid construction of biochemical pathways")]]
| |
| | | | |
| - | ===Completely Synthesizing the Genome of Mycoplasma Genitalium using Yeast Assembler===
| |
| - | In 2008, Gibson from the J. Craig Venter Institute, published an article “one-step assembly in Yeast of 25 overlapping DNA fragments to form a complete synthetic Mycoplasma genitalium genome”. In the article, the author transformed 25 overlapping DNA fragments into Yeast, homologous recombination occurs, and then the whole genome is synthesized.
| |
| - | [[file:TJU2012-Proj-LMR-fig-6.png|thumb|500px|center|'''Figure 6.''' Synthetic Mycoplasma genitalium genome (from "One-step assembly in yeast of 25 overlapping DNA fragments to form a complete synthetic ''Mycoplasma genitalium'' genome")]]
| |
| - | Construction of a synthetic M. genitalium genome in yeast. Yeast cells were transformed with 25 different overlapping A-series DNA segments (blue arrows; ~17 kb to35 kb each) composing the M. genitalium genome. To assemble these into a complete genome, a single yeast cell (tan) must take up at least one representative of the 25 different DNA fragments and incorporate them in the nucleus (yellow), where homologous recombination occurs. This assembled genome, called JCVI-1.1, is 590,011 bp, including the vector sequence (red triangle) shown internal to A86 – 89.
| |
| | | | |
| | | | |
| | | | |
| | {{:Team:Tianjin/footer}} | | {{:Team:Tianjin/footer}} |
"
