Modelling

Mathematical models are increasingly used to study certain aspects of signal transduction pathways, i.e. robustness against concentration variations [1], threshold properties and bistability [2] etc.

In an attempt to illustrate and understand the dynamics of our modified Saccharomyces cerevisiae (yeast) we created a complete mathematical model for the sequence of events when the hCG hormone binds to our modified receptor in the yeast (LH/CG receptor) and in the end starts an indigo production (click here for more information). Our model is based on the yeast pheromone pathway (click here for more information) [3].

The aim or goal of the model was to use it to analyze and understand where possible problems would occur in the lab and also to make some predictions, eg. estimates of how large concentrations of hCG is needed to, at least in theory, give an output signal, that is for indigo to be produced.

Modeling the pathway of hCG in the modified yeast

For a biochemical reaction system it is common practice to use a set of ordinary differential equations (ODE’s) to describe the changes in the concentration of a biochemical species. In a system of m biochemical species with concentration c_i (i=1,…,m) and k biochemical reactions with rates v_j (j=1,…,k) you can write:

where n_ij denote the stoichiometric coefficients.

Our model was based on a complete mathematical model of the yeast pheromone pathway (see article [4]). By modifying this model to fit our project description we were able to discern some interesting results. The changes made are that instead of having the α-pheromone bind to the Ste2-receptor we have hCG binding to the LH/CG-receptor. Also, as mentioned in the project description, the Sst2 negative feedback regulator is taken out of the system along with the cell cycle arrest reaction.

With these modifications made from the original model we made a few assumptions for our model:

• The MAPK cascade will function as usual once the hCG has bound to the LH/CG- receptor.
• The cell cycle arrest can be deleted from the model without changing any other parts in the model since it has no feedback on the rest of the system.
• The rates used for the reactions (k_i in the ODE system) are the same in our model as in the model for the yeast pheromone pathway with the exception of the degradation of hCG, the hCG binding to the LH/CG receptor and the rate in which the LH/CG receptor starts the G-protein cycle.

The modifications made to the model can be seen in figure 1 below.

Figure 1: Overview of the mathematical model for the modified yeast.

With these modifications made the system of ODE’s for our model are as follows:

With this complete mathematical model it is possible to analyze the ODE system and to make certain predictions. To do this we used MATLAB to solve the system and to plot our results.

The first thing we analyzed was the robustness of the system, that is we changed the rates k_i of the reactions in the system to see how sensitive it is for such changes. As mentioned before one assumption for our model was that all the rates are the same as in the original model (see [4]) except for the degradation of hCG (k₁), the rate in which the hCG binds to the LH/CG receptor (k₂), the rate that the hCG and LH/CG receptor disassociate (k₃) and the rate that starts the G-protein cycle (k₆) so those were the only ones changed. Since it is unknown how these rates changes with our modified yeast we tried different ones to get some results. It is known that the degradation of hCG is much slower than that of the α-pheromone so that particular rate (k₁) was changed according to [5]. For the other rates we assumed that the original rates (those used in the original model [4]) was the best ones and we gradually made them worse.

One of the main predictions we wanted to make was to see how much Ste12 would be produced given an initial concentration of hCG. This since Ste12 is what starts off the indigo production. We therefore solved the system with different rates used for k₁, k₂, k₃ and k₆ and an initial concentration of hCG starting on 0.0067 nM (which is the average concentration with a pregnant woman 3 weeks since the last menstrual bleeding) and then changes according to how the hCG concentration changes with a pregnant woman [6]. The other initial values was the same as in the article [4]. The result of this can be seen in figure 2.

Figure 2: Concentration of Ste12 for different parameters and different initial concentrations of hCG. Bad parameters are the fraction 1/10, 2, 1/10 of the original yeast parameters k₂, k₃ and k₆. In a similar fashion the fractions for the worse parameters are 7/100, 2.2 and 7/100 and for the worst parameters they are 1/100, 2.5 and 1/100.

As can be seen from figure 2 the parameters make a big difference for small initial values of hCG but as the concentration increases the parameters make less difference for the output. It can also be seen that the worst rates hardly gives an output at all for small concentrations of hCG.

The other main prediction we wanted to make from the model was to see how the deletion of the Sst2 negative feedback would affect the system. We therefore solved the ODE system with and without the Sst2 feedback. These two systems was solved with the same initial concentrations of hCG as before and with the rates we thought most plausible (red line in figure 2). The result is visible in figure 3 below.

Figure 3: Concentration of Ste12 with and without the Sst2 negative feedback and with different initial concentrations of hCG.

As can be seen in figure 3 the deletion of the Sst2 negative feedback doesn’t affect the output signal significantly for small concentrations of hCG but does so for larger concentrations of hCG.

The yeast is supposed to function as a pregnancy test so we were mostly interested in how much Ste12 is produced for small concentrations of hCG and in the first twenty minutes since for the test to be of use as a pregnancy test you would want to be able to get results early in the pregnancy (about three weeks after the last menstrual bleeding) and after a short time period.

Conclusions that can be made from our analysis of the model is that for the yeast pregnacy test to work early in an pregnancy:

• The binding of hCG to the LH/CG receptor has to work almost as well as the binding of the α-pheromone to the Ste2 receptor.
• To get a sufficiently good output signal the rate in which hCG and the LH/CG receptor disassociate can’t be to high.
• The LH/CG receptor has to be able start the G-protein cycle with a rate that is at least 10% of the rate in the real yeast pheromone pathway.
• The Sst2 negative feedback does not, as mentioned earlier, affect the output signal significantly for small concentrations of hCG and it is possible that it can be held intact and the system would still work but for best possible output it should be deleted.

To see how this worked out in reality go to our result page.

References

With many thanks to our generous sponsors: