Team:SDU-Denmark/labwork/Notebook/week3

Laboratory Notebook

Here you find the log book for the procedures carried out in the laboratory, starting from week 27.

19-07-2012:

Another digestion, plated SST cultures and Miniprep on FFT

The plated SST from yesterday didn’t give any colonies. We tried a different procedure where we use the PCR purification from SST and the pJET plasmid digested with EcoRV in a gel.
We then made a gel purification on both bands at the same time.
The purification was eluted in 30μl elution buffer, and then we used 7μl of the elution with 0,5μl ligase and 2,5μl ligase buffer in order to ligate the gene into the vector. This was plated on amp-agar plates and incubated O.N.

We also made Miniprep on the 10 liquid colonies with FFT, then digested it with EcoRI and PstI.
The digest was ran on a gel and proved results from FFT coloni 3 and 9 which had two bands corrosponding to our vector and gene.
We measured the concentration on the two tubes using the nano-dropper and got the following concentrations:
Tube#3: 138,2ng/µl
Tube#9: 71,8ng/µl
This was enough reason to send them off for sequencing.
Seeing as we needed to send of four tubes per sample with 15µl per tube, we didn’t have enough volume in tube#9, so we only prepared four tubes to be send off for sequencing of tube#3, as it had a slightly higher concentration than the 100ng/µL maximum, so we just added another 20µl of elution buffer for a total volume of 67µL in tube #3, which was then split into four tubes of 15µL and labelled with barcodes.
Furthermore we made 8 new coloni PCR’s from the original FFT amp. agar plate. But we only got very small parts shown on the gel so it wasn't a success.
For the sequencing, we need four primers, a pJET1.2_for and _rev and then 2 primers that would anneal on the FFT gene. We used the MWG sites primer design tool (http://www.eurofinsdna.com/) to design primers that anneal to the FFT gene.
Seeing as the FFT gene is approximately 1800bp long the primers were designed to anneal somewhere between positions 450-500 and 950-1000 both in the forward direction, to be sure that the entire gene is sequenced.
Of the 10 random cultures that were put into liquid LB and left in incubator O.N. on 18/7 only tubes 3 and 9 were viable. We decided to make some more liquid culture of these bacteria and let them incubator at 37°C O.N.

This is to be sure that tomorrow we have enough sample/volume of tube#9 in order to send it off for sequencing.

20-07-2012:

DNA extraction from O.N. liquid cultures

Overnight cultures incubated at 37°C in Ampicilin containing medium:
- 10 FFT liquid cultures
- 6 SST liquid cultures

The 16 cultures was extracted and a Nanodrop measured the concentrations:
Run 3: 116,1 ng/µl
Run 9: 10,8 ng/µl (discarded, useless for sequencing at this low concentration)

For the preparation of liquid culture for overnight incubation we marked and transferred single-unit colonies from FFT plates(10) and SST plates(6) to 3mL ampicilin containing liquid medium.

21-07-2012:

Gel electrophoresis on extracted cuktures of FFT and SST

We did a cryo “backup” of the liquid cultures from yesterday, containing the FFT and SST genes. The bacteria cultures was lysed and the plasmids was extracted using GeneJET Plasmid Miniprep Kit. A Nanodrop analysis was made from our extracted plasmids which should contain our FFT- and SST-gene. A gel was constructed and our plasmids was ran through an electrical current at 100V. INSERT PICTURE HERE!!!!!!!! There were no usable results from the gel electrophoresis. For future studies we should try to digest the plasmids with the restriction enzymes for a longer period.