Team:MIT/NOTGate

From 2012.igem.org

Revision as of 02:18, 27 October 2012 by Felixsun (Talk | contribs)

iGEM 2012

Overview

  • Results Overview

Circuit Production

  • Short RNA Production
  • Circuit Production: Hammerhead Ribozymes

NOT Gate

  • Design
  • Modeling
  • In Vitro Results

Sensing

  • Design
  • Modeling
  • In Vitro Results

Actuation

  • TuD and Decoy RNAs
  • Modulating Hammerheads

The Key Reaction

  • Design
  • Nucleic Acid Delivery
  • Experimental Strand Displacement

Our BioBricks

  • Favorites
  • All BioBricks

Attributions

  • Attributions

Our NOT Gate Design, Simulations and Optimization

Design

The NOT gate (signal inverter) design we eventually used comprises of multiple double- and single-stranded species. The most important of these are NOT gate (A), output (B) and buffer (C) complexes.
There are two cases to consider: first the case where there is no input present (in digital terms, the input is 0), and second the case where there is a saturating level of input (digitally represented as a 1). We aim to convert the '0' input into a '1' output and the '1' into a '0' - the basic operation of a NOT gate. Refer to the diagram below throughout the explanation.

Case 1: No input present -> high signal
Here, the output strand (B) reversibly reacts with the NOT gate (A). The reaction is reversible because the output strand only displaces the green section on the NOT gate, but not further, meaning that the reaction could go back as well. This reversible reaction allows the output strand to react to a downstream buffer (C) and amplifier (D) to produce a high signal (a new active nucleic acid strand is released).

Case 2: Input present -> low signal
Here, the input strand and output strand both react with the NOT gate. The input strand displaces up to the pink region and the output strand displaces up to the green region. This is irreversible, as once strand displacement happens from both sides, the complex separates into two double-stranded species. There is no toehold to initiate the reverse reaction, so the output strand is "stuck". The output therefore cannot be buffered or amplified to produce a signal: no new active nucleic acid strand is released.

Our NOT Gate Design
Diagram of our NOT gate. See the paragraph above for a more detailed description.

Initial Simulations

We initially designed three NOT gates, each using different components.

Design 1:

Design 2:

Design 3:

We simulated each of these designs in Visual DSD, a program designed to simulate strand displacement reactions. Based on our simulation results, we decided to design the sequence, order, and test the third design.


A sample of Visual DSD code.


A reaction diagram generated by Visual DSD, based on the above code.


The results of our simulation. The final design is compared against an earlier design.

In Vitro Results for Our NOT Gate

To test the functionality of the NOT gate as expressed by its transfer function (relating the input levels to output signal strengths) we performed in vitro studies with DNA as the nucleic acid for strand displacement. The output signal strand was fed to a reporter complex. This reporter, when triggered by a signal, will fluoresce in the red channel. Our experiments measured these fluorescence levels for various amounts of initial input levels using a plate reader.

Optimization

The original in vitro test showed a result that did not match our simulated transfer function.

All inputs at equal concentrations, 1pmol

From the simulations, we knew that by increasing the concentration of the dynamic gate (complex A), we would get a more digital signal. We implemented this strategy by increasing the relative concentration of strand A by various amounts. Looking at the low dip in the middle concentration ranges and the rise afterwards, we determined that the cooperative hybridization was not working at the levels we were using. To test this, we raised the absolute concentration of all the parts of the NOT gate and kept the high relative concentration of complex A. This resulted in a transfer function that very nearly matched our simulation and gave us NOT gate behavior.


Concentration of strand A is 1.4X, where X = 20pmol.