Team:HokkaidoU Japan/Notebook/plastic protocols

From 2012.igem.org

(Difference between revisions)
(→Culture and harvest)
(→Polymer producing media)
Line 11: Line 11:
|-
|-
|2×LB
|2×LB
-
|10ml
+
|10 ml
|-
|-
|●50% Glucose
|●50% Glucose
-
|800ul
+
|800 ul
|-
|-
|●1M pantothenic acid Ca
|●1M pantothenic acid Ca
-
|200ul
+
|200 ul
|-
|-
|Amp(100mg/ml)
|Amp(100mg/ml)
-
|20ul
+
|20 ul
|-
|-
|ROwater
|ROwater
-
|8.98ml
+
|8.98 ml
|-
|-
|}
|}
-
Put 1.5ml each into the test tube.
+
Put 1.5 ml each into the test tube.
Line 33: Line 33:
|-
|-
|ROwater
|ROwater
-
|7ml
+
|7 ml
|-
|-
|Glucose
|Glucose
-
|10g....Heat　and stir until it melts.
+
|10 g....Heat　and stir until it melts.
|-
|-
|ROwater
|ROwater
-
|up to 20ml
+
|up to 20 ml
|-
|-
|}
|}
Line 50: Line 50:
|-
|-
|ROwater
|ROwater
-
|7ml
+
|7 ml
|-
|-
|pantothenic acid Ca
|pantothenic acid Ca
-
|4.77g....Heat　and stir until it melts.
+
|4.77 g....Heat　and stir until it melts.
|-
|-
|ROwater
|ROwater
-
|up to 10ml
+
|up to 10 ml
|-
|-
|}
|}

Revision as of 05:35, 19 August 2012

Bold text

Polymer producing media

polymer producing media (LB:2%Glc+ 10mM pantothenic acid Ca + Amp100mg/l) 20ml

2×LB 10 ml
●50% Glucose 800 ul
●1M pantothenic acid Ca 200 ul
Amp(100mg/ml) 20 ul
ROwater 8.98 ml

Put 1.5 ml each into the test tube.


●50%gulcose

ROwater 7 ml
Glucose 10 g....Heat　and stir until it melts.
ROwater up to 20 ml

Filter sterilize.


●1M pantothenic acid Ca

ROwater 7 ml
pantothenic acid Ca 4.77 g....Heat　and stir until it melts.
ROwater up to 10 ml

Filter sterilize.


Culture and harvest

  1. Preculture transformed media 1.5ml for 10～14 hours, 180rpm/30℃.
  2. Culture 15μl preculture media in polymer producing media for 48hours, 180rpm/30℃.
  3. Centrifuge for 10min, 5000rpm.
  4. Remove supernatant and add 500ml ROwater and suspend it.
  5. Centrifuge again for 10min, 5000rpm and remove its supernatant.
  6. Freeze in -80℃ for more than 3hours.
  7. Freeze-dry for more than 48hours.

Polymer extraction and purification

  1. Move dried up bacteria into test tube.
  2. Break up them to separate and add 10ml chloroform.
  3. Incubate for 48hour at 60C.
  4. Make it filtered through PTFE and move it into another test tube.
  5. Volatilize organic solvent by exposing air and separate polymer.
  6. Add 5ml hexane and voltex for a minute. After centrifuging (1,500rpm, 10min), remove the clear layer.
  7. Volatilize chloroform by exposing air again.
  8. Add 5ml MtOH, voltex for a minute, centrifuge (1,500rpm, 10min), and remove the clear layer.


</div>

Retrieved from "http://2012.igem.org/Team:HokkaidoU_Japan/Notebook/plastic_protocols"