Team:Cambridge/Project/Instrumentation

From 2012.igem.org

(Difference between revisions)
(Mechanical)
(Mechanical)
Line 7: Line 7:
The mechanical chassis prototype, as can be seen from the image on the left, was made using two materials: foam and aluminium. Foam was chosen due to its easy manipulation and aluminium due to its excellent strength to weight ratio. The prototype includes a rotary mechanism (a central metal axon is connected to the cuvette holder cylinder), which can be  driven in steps by a DC electric motor (and a suitable code).
The mechanical chassis prototype, as can be seen from the image on the left, was made using two materials: foam and aluminium. Foam was chosen due to its easy manipulation and aluminium due to its excellent strength to weight ratio. The prototype includes a rotary mechanism (a central metal axon is connected to the cuvette holder cylinder), which can be  driven in steps by a DC electric motor (and a suitable code).
-
[[File:Cuvette_holder_function.jpg|80px|thumb|right|Cuvette holder coated with mylar film concentrating light from bio-luminescent bacteria]]
+
[[File:Cuvette_holder_function.JPG|80px|thumb|right|Cuvette holder coated with mylar film concentrating light from bio-luminescent bacteria]]
The purpose is that our self-developed sensor, which was made using two light dependent resistors (and can be seen in the design page), an orange and a blue theatrical filter, takes multiple readings from different biosensors, each found in a different cuvette. It should be noted that each cuvette holder is coated on the inside with highly reflective mylar film (image on the right). In this way, most of the light produced by the bacteria is concentrated for more accurate sensor measurements.
The purpose is that our self-developed sensor, which was made using two light dependent resistors (and can be seen in the design page), an orange and a blue theatrical filter, takes multiple readings from different biosensors, each found in a different cuvette. It should be noted that each cuvette holder is coated on the inside with highly reflective mylar film (image on the right). In this way, most of the light produced by the bacteria is concentrated for more accurate sensor measurements.

Revision as of 23:27, 24 September 2012

Previous iGEM teams have charaterised an impressive array of inducible promoters, along with other elements of biosensing circuitry... Read More






Contents

Instrumentation

Instrumentation was a vital aspect of our project in the development of the kit. The term instrumentation includes all the mechanical, electrical and software components which allow the incorporation of our multiple independent modules into a working kit. The design process as well as the testing data and videos of the different parts of the instrumentation can be reviewed at our Design page

Mechanical

Mechanical chassis

The mechanical chassis prototype, as can be seen from the image on the left, was made using two materials: foam and aluminium. Foam was chosen due to its easy manipulation and aluminium due to its excellent strength to weight ratio. The prototype includes a rotary mechanism (a central metal axon is connected to the cuvette holder cylinder), which can be driven in steps by a DC electric motor (and a suitable code).

Cuvette holder coated with mylar film concentrating light from bio-luminescent bacteria

The purpose is that our self-developed sensor, which was made using two light dependent resistors (and can be seen in the design page), an orange and a blue theatrical filter, takes multiple readings from different biosensors, each found in a different cuvette. It should be noted that each cuvette holder is coated on the inside with highly reflective mylar film (image on the right). In this way, most of the light produced by the bacteria is concentrated for more accurate sensor measurements.

Electrical

Blusmirf Gold Bluetooth Modem
Arduino circuitry

The hardware/software electronic interface was achieved using an Arduino microcontroller. The arduino circuitry, as illustrated on the left, is made up of our sensor, the motor, and a PCB or a breadboard (both were used in the process of our project). It should be noted that the final setup we developed does not have a second transistor for driving the motor, as the motor used did not provide a great initial torque. However, in cases where the motor to be used is too violent at start a second transistor is required. The Bluetooth modem (Bluesmirf Gold) is an extra to be used when communication with mobile devices (e.g. Android) is required. The LDRs of our sensor sit in a biased potential divider setup allowing for a direct ratiometric output without further calculations needing to be made in the software (more information, including testing data for our sensor can be found in the design page as well). The circuitry is incorporated into the mechanical chassis for an attractive, ergonomic overall design. The functionality of the system, including the sensitivity of our manually-made sensor setup in the right geometry using our manually-made cuvette holders was tested with success! The results can be seen in our Design page. The code of the pre-set C++ program for driving the arduino can be found and downloaded in our Arduino Code pageNote that there are two different programs: one for PCs and one for android devices.

Software

Software applications were developed, as mentioned before, for both PCs and android devices. This was done in order to provide extra flexibility as the potential use of our kit is field work. The computer software is written in the free open-source language python with cross-platform wxWidgets used to implement a GUI. The idea was to develop a fully functional GUI for collecting sensor data from all six inputs and display these as line graphs and in a final bar chart.

The image on the right is a screengrab of the GUI under development and testing its ratiometric ability. The higher values are when one sensor is covered, the lower for the other and no change is observed when both are illuminated equally. By controlling the illumination, we managed to make our application write iGEM in morse code (image on the right)! The android GUI was made in Java using Eclipse editing mostly [http://www.amarino-toolkit.net/index.php/home.htmlAmarino] projects' open-source code (General Public License). The first screen (image on the left) asks for the address of the Bluetooth modem connected to Arduino. B.Subtilights was the first logo of our team, thus included in our application. This application is also functional as it can successfully connect, read real-time data and plot them in any Android phone/tablet.

The code (for programmers) as well as a ready application to be downloaded (for non-programmers this is the Bio_Logger.apk file) can be found in our Android application page

It should be noted that amarino_2.apk, found in the link above must also be downloaded on the android device for our application (Bio_Logger) to be perfectly functional, as it requires one of the amarino libraries.

Android application start page
Python program for PC